The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We've come across this article pertaining to Installing A Bathtub down the page on the web and decided it made perfect sense to discuss it with you over here.
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old tub is easily obtainable, the project can move rapidly; if you have to open a wall to remove the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the brand-new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to employing a professional to take over a halfway-completed job, it is better to think about employing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will certainly help you set up a new tub in your bathroom if you have currently bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and material checklist must comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers are in place in between the tap as well as the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing both wood boards under its feet, put the tub in the required position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Fill up the tub and additionally examine the overflow outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bath tub has actually been made use of at the very least when as this will certainly settle it into its last placement.
Preparing for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the activity experienced when the tub remains in usage. The sealer can fracture fairly very early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the market. It is recommended to fit the floor tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated by Installing A Bathtub and I'm hoping you liked the entire page. Don't hesitate to take a moment to promote this blog post if you enjoyed reading it. I am grateful for your time. Visit us again soon.
Set An Appointment Report this page